f95 downfall

A magician's fake thumb is a small prop that is used by magicians to create the illusion of making objects disappear or appear in their hands. It is a clever device that allows magicians to perform tricks that seem impossible to the audience. The fake thumb is usually made of plastic or rubber and is designed to resemble a real human thumb. It is hollow inside and has a small hole at the bottom that fits snugly over the magician's real thumb. The fake thumb is slipped onto the magician's thumb before the trick begins, and it is hidden by the magician's hand or other props during the performance. One of the most commonly performed tricks using a fake thumb is the classic "vanishing thumb" trick.

One of the most commonly performed tricks using a fake thumb is the classic "vanishing thumb" trick. The magician starts by showing the audience their thumb, then makes a gesture as if to pluck the thumb off. When they open their hand, the thumb appears to have vanished.

Spare Tire Holder Suggestions

I have a 2014 21’ Key West Bay Reef that I would like to attach 2 spares to my Magic Tilt dual axle trailer. Any suggestions?

Sent from my iPhone using Tapatalk

Oct 22, 2021 #2 2021-10-22T17:41

I used one of these on my single axle Magic Tilt. I had to add some spacers under it to get it fit on my trailer, which has four inch tall I-beams. If your I-beams are at least five inches tall it should fit fine.
https://www.easternmarine.com/aluminum-i-beam-spare-tire-carrier-86064-0

You might want to consider using one of the tire mounts that uses a bearing hub instead of lug nuts to mount the spare. You'll have a spare hub in case of a bearing failure, and you won't need a lug wrench to change the tire, just a pair of pliers.

Oct 22, 2021 #3 2021-10-22T19:08

So you had to drill into trailer then correct?

Sent from my iPhone using Tapatalk

Oct 23, 2021 #4 2021-10-23T00:59

Yes, you have to drill four 1/2 inch holes in the web. (The instructions say 5/8, but if you drill them accurately half inch works.) I put mine close to the front end of the beam where it shouldn't affect the trailer's strength. The mount comes with grade 5 steel bolts; I replaced mine with 304 stainless. They want you to put a layer of duct tape between the galvanized mount and aluminum beam to prevent galvanic action, which I did.

Oct 23, 2021 #5 2021-10-23T11:58

Yes, you have to drill four 1/2 inch holes in the web. (The instructions say 5/8, but if you drill them accurately half inch works.) I put mine close to the front end of the beam where it shouldn't affect the trailer's strength. The mount comes with grade 5 steel bolts; I replaced mine with 304 stainless. They want you to put a layer of duct tape between the galvanized mount and aluminum beam to prevent galvanic action, which I did.

You might want to re-think the stainless bolts. It's likely that they want the grade 5 bolts in there so that the mounting flange of the tire holder acts as a flitch plate to offset the effect of drilling the holes in the i-beam. How critical, I cannot say without some calculations. But I see that a lot with trailer hardware. Quite a few parts on aluminum trailers use galvanized steel and galvanized grade 5 or grade 8 bolts.

Oct 23, 2021 #6 2021-10-23T12:27

This is the one I’m thinking about.

Sent from my iPhone using Tapatalk

Oct 23, 2021 #7 2021-10-23T23:16

That will work if your trailer tongue is long enough. Mine isn't. Note that the location of the spare will affect how sharp you can jackknife the trailer.

The Tie Down Engineering stuff is well made. Hot-dipped galvanized, not just electroplated.

Oct 23, 2021 #8 2021-10-23T23:45

You might want to re-think the stainless bolts. It's likely that they want the grade 5 bolts in there so that the mounting flange of the tire holder acts as a flitch plate to offset the effect of drilling the holes in the i-beam. How critical, I cannot say without some calculations. But I see that a lot with trailer hardware. Quite a few parts on aluminum trailers use galvanized steel and galvanized grade 5 or grade 8 bolts.

I can't see how slightly stronger bolts will make the I-beam any stronger. At any rate, I placed the mount in a low-stress area, near the end of the beam and where it's supported by the galvanized trailer tongue.

Oct 24, 2021 #9 2021-10-24T00:33

You might want to re-think the stainless bolts. It's likely that they want the grade 5 bolts in there so that the mounting flange of the tire holder acts as a flitch plate to offset the effect of drilling the holes in the i-beam. How critical, I cannot say without some calculations. But I see that a lot with trailer hardware. Quite a few parts on aluminum trailers use galvanized steel and galvanized grade 5 or grade 8 bolts.

I can't see how slightly stronger bolts will make the I-beam any stronger. At any rate, I placed the mount in a low-stress area, near the end of the beam and where it's supported by the galvanized trailer tongue.

It's how the loads in the i-beam transfer to the plate on the tire holder -- the plate becomes a reinforcement to offset the weakening of the i-beam from holes. Many different bits of trailer hardware are designed to do this. It will be dependent on the strength of the bolts to transfer the load. May not matter in this case, but that is likely why grade 5 bolts were specified for something as simple as a tire holder. SS bolts are going to be like rubber in comparison.

Home :: PV - Spare Tire Mounts :: PV1900 ~ SPARE TIRE MOUNT HORIZONTAL WITH LOCK

In reality, the magician has simply hidden their real thumb inside the fake thumb, giving the illusion that it has disappeared. Another popular trick using a fake thumb is the "appearing thumb" trick. In this trick, the magician starts with an empty hand and then makes a motion as if they are pulling something out of thin air. When they open their hand, a thumb appears to have appeared magically. Again, this is achieved by hiding the real thumb inside the fake thumb and then revealing it at the right moment. The fake thumb is a versatile prop that can be used in many different tricks and routines. It allows magicians to manipulate objects and create the illusion of magic in a way that is entertaining and captivating for the audience. However, mastering the use of the fake thumb requires a lot of practice and dexterity to ensure that the trick is performed smoothly and convincingly. In conclusion, a magician's fake thumb is a small but essential tool for creating illusions and performing magic tricks. It enables magicians to make objects disappear or appear seemingly out of thin air, adding an element of mystery and wonder to their performances. The use of the fake thumb requires skill and practice, but it can greatly enhance a magician's repertoire of tricks..

Reviews for "f95 downfall"

f95 downfall